Error 13

Despues de haber utilizado la caja con total normalidad recibo error 13 mientras el piloto parpadea en rojo y verde alternativamente y me suelta un rolo del tipo que tengo que ir al servicio tecnico con la X.
Lo curioso es que si la enciendo con un disco cargado lo ejecuta bien, ya sea DVD original o sea un Backup.
El servicio ftp no responde.

Gracias por vuestra ayuda.....

Saludos

Adjuntos

revisa el c de tu xbox pq me huele a q no es capaz de encontrar el xboxdash.xbe o el evoxdash.xbe
He conseguido aarncar el server FTP con un Boot Cd de Evox y la particion C esta totalmente vacia pero todas las demas particiones estan perfectas.
Tambien he intentado transferir el contenido del cd pero no me ha dejado, es como si la particion estuviese rota o algo asi.

Estoy preocupado por el tema. :?
T recomiendo q en stos casos utilices el Slayer para crear d nuevo las particiones. Perderas todo lo q tenga en el HD, por lo q deberias hacer una copia d seguridad en el PC.

Salu2
Formatea /c y luego sube por ftp el contenido de tu backup de /C. Si no lo tienes prueba a poner el disco antiguo...

pd: El slayer es una mierda... es mejor si no quieres complicarte y perder todo tu F pero si quieres saber como funciona la x es mejor a mano
No tengo Respaldo de La xbox.

Como puedo formatear C????

Ke puedo hacer, podre clonar el disco de otra X?????

Sabeis alguno si es posible encontrar el una imagen de disco de la X???

Ahora funciona todo con disco de arranque ke me he currado, pero el menu original ni rastro claro.

Gracias a todos

Satanas os cuida
Instructions:

1) Make a Norton Ghost 2002 boot disk. (There are other programs that will do bit for bit copying but Norton was the easiest for me here). If you use something else and it don’t work, I reserve the right to say ‘I told you so’).

2) Set the Jumper(s) on the original hard drive so that the HDD is master and install it into your PC.

3) Set Jumper(s) on the hard drive to be cloned so that the HDD is slave and install it on the same IDE channel in the PC.
note: You can do the Original as Master on IDE1, and the Clone as Master on IDE2, but be CAREFUL NOT to kill your original HDD by overwriting the clone to it. Doing as outlined here makes it more ‘obvious’ as to what should be copied where… however, proceed at your own peril.

4) Make sure your computer CMOS is set to boot to the floppy first and boot the computer off the Ghost 2002 boot disk.

5) Once the program loads, go to the menu and quit or exit to DOS.

6) Re-execute Ghost from DOS but this time add the switch “/ir”. At the DOS prompt type: “ghostpe /ir”. This will allow Ghost to simply copy bit for bit on the clone rather than try to read the image on the original HDD as a valid FAT32 or NTFS.

7) When Ghost has loaded this time, open the menu and go to “Disk” and then “to Disk”.

8) Select the original hard drive as the source. (If you jumpered the original as the master it will be the top drive to select in the menu and will have a “Raw Image”)

9) Select the new hard drive as the destination and give her nuts.

10) This process will take about 45 minutes to clone an 80 gig hard drive depending on your computer speed.

11) When the clone is finished, the new hard drive should work identical to the original in any modded xbox that supports HDD swap.

12) Take the hard drives out of the PC and rejumper them to what they were before you installed them into the computer, most likely CS (cable select) or MAS (master).

13) Install them back into the XBOX or put the back up hard drive in a safe place and you are done.

14) This will work in place of installing a hard drive and portioning it via ftp if you are swapping hard drives on an xbox. You will just need to find someone with a hard drive you can clone.
6 respuestas